Schedule A Free Estimate

How do you feel with regards to Tools You Need to Install a New Bathtub ?

Installing a bath tub isn't precisely brain surgery, however it does call for solid plumbing, woodworking, and often, tiling abilities. Replacing an old tub with a brand-new one is also a moderately challenging task. If the old tub is easily accessible, the project can relocate speedily; if you have to open up a wall surface to remove the old tub and also position the new bathtub, the job is a lot harder. In either case, the job is within a residence handyman's skills, although you will need a helper to leave the old bathtub and set in the new one. Make certain you have actually qualified yourself for the task and also are comfortable attempting it. Instead of employing a contractor to take over a halfway-completed job, it is far better to take into consideration using one prior to you start. Chances are you may need a professional plumber to make tube connections.
This short article will help you set up a new tub in your washroom if you have actually already bought a new tub as well as do not require to alter the arrangement of your previous water supply pipelines.
Your devices as well as material list need to make up the following:

• New Tub


• Hammer


• Pipeline Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Flexible Wrench


• Putty Blade


• Screwdriver


• Cold Knife


• Measuring tape


• Pipeline Caps


 

Getting ready for the Setup

First of all, the supporting framework supplied with the bath ought to be fitted (if needed) according to the producer's directions. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is important to make sure that if the faucet features a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is likewise practical to fit a supporting plate under the faucets system to avoid strain on the bath tub.
Fit the versatile tap connectors to the bottom of both faucets using 2 nuts and also olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Make sure you utilize all of the provided washing machines.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom must now prepare to be fitted in its last position.

Removing Old Touches

If you need to change old taps with brand-new ones as a part of your installation, after that the first thing you should do is separate the water. After doing so, turn on the taps to drain pipes any type of water continuing to be in the system. The process of getting rid of the existing taps can be fairly problematic as a result of the restricted gain access to that is frequently the instance.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the faucets. Have a cloth ready for the continuing to be water that will certainly originate from the pipes. As soon as the supply pipelines have been eliminated, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the single faucets from turning throughout this procedure. Once the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleansed of any old sealing substance.
Before carrying on to fit the brand-new taps, contrast the pipe links on the old faucets to the new taps. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new taps to fit.

Setting up the Bath tub

Using the two wood boards under its feet, position the bathtub in the needed placement. The wood boards are useful in equally spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto 4 little factors.
The following objective is to guarantee that the bath tub is leveled all round. This can be achieved by inspecting the level and changing the feet on the tub till the spirit level checks out degree.
To install taps, fit all-time low of the outermost flexible tap port to the ideal supply pipeline by making a compression sign up with; then do the same for the other faucet.
Switch on the supply of water and also examine all joints and new pipework for leakages and also tighten them if essential. Fill the tub as well as also examine the overflow electrical outlet and also the normal outlet for leaks.
Lastly, deal with the bathroom paneling as described in the manufacturer's instruction manual. Tiling as well as securing around the bath tub must wait till the bath tub has been utilized a minimum of when as this will certainly resolve it right into its last placement.

Fitting New Taps

If the tails of the new taps are plastic, then you will need a plastic connector to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap and the other end offers a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will need decreasing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, position the tap in the mounting opening in the bath/basin ensuring that the washing machines remain in area in between the faucet as well as the sink. Protect the tap in place with the producer given backnut. As soon as the faucet is safely in position, the supply pipelines can be attached to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with normal faucet adapters. The previous type ought to be connected to the faucet finishes initially, tightening only by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have actually been attached.

Tiling Around the Bath tub

In the area where the bath meets the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is necessary as the fitting can move enough to crack a rigid seal, creating the water to pass through the wall surface between the bath and the tiling, leading to complications with wetness and also feasible leaks to the ceiling below.
You can choose from a selection of coloured sealers to assimilate your fixtures and installations. They are sold in tubes and cartridges, and also can securing spaces as much as a width of 3mm (1/8 inch). If you have a bigger space to fill, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to constantly fill the bathtub with water before sealing, to allow for the activity experienced when the bathtub remains in use. The sealant can crack fairly very early if you do not think about this activity prior to securing.
Additionally, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also conveniently offered on the market. It is advisable to fit the tiles making use of water-resistant or waterproof glue as well as grout.

How to Install or Replace a Bathtub

Find Your Dimensions

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

 

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

Disconnect the Water Supply and Drain Assembly

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

 

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

 

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

Cut Out the Old Tub

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

 

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

 

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

Install the New Tub

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

 

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

 

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

 

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

Secure the Tub

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

 

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

 

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

 

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

I discovered that blog post about How to Install a Bathtub while doing a lookup on the internet. Sharing is good. Helping people is fun. Many thanks for going through it.

Top Article